Installing Windows 11 (from ISO) on real hardware (without SB and/or TPM 2.0 support)

Created: June 20, 2021 Last Update: June 20, 2021
Authors: Gustave Monce, Daniel Kornev
Status: Draft
Supported Windows 11 Version: 21996.1



Here's some quick notes on installing Windows 11 on real hardware from ISO in case when hardware doesn't support TPM and/or SB (Secure Boot). For this example, we're assuming a system with no other critical disks installed, and a helpful host system being around to set up the initial image.

This guide has been created for the 21996.1 version of Windows 11.



  • Windows 10 Iron or Cobalt (20279 or 21xxx+) - though 20H2 can also work just fine
  • Utility USB flash drive of ~8GB+


  • Boot drive larger than 50 GiB

Common: Files & Tools

  1. Download Windows 11 ISO
  2. Download Windows USB/DVD Tool
  3. Install it

Prepare USB Drive for Flashing

  1. Get an empty USB Flash drive (with size at least 8GB)
  2. Use Windows USB/DVD Tool
  3. Follow its instructions to flash your Windows 11 ISO onto the USB Flash drive

Apply Your Image

Clean Disk & Lay Out Partitions

  1. Boot from USB Flash drive
  2. Open diskpart
  3. Type this:
list disk

Take a note of the name of your device's main disk drive, e.g., disk 0 4. Type this (where disk 0 is your device's main disk drive):

select disk 0
  1. Follow the instructions for UEFI-based PCs from to properly lay out your device's main disk for Windows 11 installation:
rem == CreatePartitions-UEFI.txt ==
rem == These commands are used with DiskPart to
rem    create four partitions
rem    for a UEFI/GPT-based PC.
rem    Adjust the partition sizes to fill the drive
rem    as necessary. ==
select disk 0
convert gpt
rem == 1. System partition =========================
create partition efi size=100
rem    ** NOTE: For Advanced Format 4Kn drives,
rem               change this value to size = 260 ** 
format quick fs=fat32 label="System"
assign letter="S"
rem == 2. Microsoft Reserved (MSR) partition =======
create partition msr size=16
rem == 3. Windows partition ========================
rem ==    a. Create the Windows partition ==========
create partition primary 
rem ==    b. Create space for the recovery tools ===
rem       ** Update this size to match the size of
rem          the recovery tools (winre.wim)
rem          plus some free space.
shrink minimum=500
rem ==    c. Prepare the Windows partition ========= 
format quick fs=ntfs label="Windows"
assign letter="W"
rem === 4. Recovery partition ======================
create partition primary
format quick fs=ntfs label="Recovery"
assign letter="R"
set id="de94bba4-06d1-4d40-a16a-bfd50179d6ac"
gpt attributes=0x8000000000000001
list volume
  1. Mark your Windows partition as active in diskpart:
list partition
note the name of your Windows partition (e.g., "partition 3")
select partition 3
  1. Type exit to leave diskpart

Apply Image

  1. Check which OS SKU you want to install:
dism /Get-WimInfo /WimFile:D:\Sources\install.wim <— here D:\ is the drive name of your USB drive
  1. Remember its index and use it to apply its image to your Windows partition (e.g., "W"):
dism /Apply-Image /ImageFile:D:\Sources\install.wim /index:1 /ApplyDir:W:\
  1. Create boot records:
W:\Windows\System32\bcdboot G:\Windows

If you'll see "Failure when attempting to copy boot files" error message then use this command instead:

W:\Windows\System32\bcdboot c:\windows /s s: /f ALL
  1. Type exit in the Command Prompt window

Load Windows 11

At this time, your Windows 11 will boot. If everything is correct you should see the OOBE.

Revision #4
Created Sat, Jun 19, 2021 9:41 PM by Daniel Kornev
Updated Sun, Jun 20, 2021 11:21 AM by Daniel Kornev